A plain-English explainer of AS/NZS 2201.1, the joint Australian/New Zealand standard for intruder alarm systems on the client's premises. It covers what the current 2007 edition is, how it sits next to the other parts of the 2201 series, whether anyone actually has to follow it, the main topics it addresses, and the 2026 draft that was opened for public comment.
It is not the standard itself, not compliance advice, and not legal advice. The full text of both the 2007 edition and the 2026 draft is sold or released through Standards Australia and Standards New Zealand; this post does not reproduce that text, and it does not invent clause numbers, standby times, sound levels or service intervals. Where I can only confirm that a topic exists, I say so and point you at the standard. If a fact matters for a live job, a quote, an insurance claim or a tender, buy or view the current official edition and read that, or get advice from a licensed installer or the relevant regulator.
Companion threads already cover who needs a licence to install alarms, CCTV or access control in Australia, CCTV, doorbell and NVR privacy rules, and maglocks, emergency releases and fire-exit rules. Those are separate regimes. This post is about the intruder-alarm standard.
Complexity
Reading: beginner to intermediate. Installing, maintaining or repairing security equipment for other people is licensed work in most of Australia — see the licensing thread above — and electrical wiring work is a different licence again (Australian electrical compliance for smart-home work).
1. What AS/NZS 2201.1 is
The current published edition is AS/NZS 2201.1:2007, Intruder alarm systems, Part 1: Client's premises — Design, installation, commissioning and maintenance. It was published on 12 April 2007, runs to 34 pages, and is a joint Standard of Standards Australia and Standards New Zealand. It was prepared by joint technical committee EL-031 (then titled Intruder Alarm Equipment and Installations). It originated as AS 2201.1-1978, and the 2007 edition jointly revised and redesignated the previous Australian edition, AS 2201.1-1998.
The Standards Australia store still lists this edition as the published document, with the status Pending Revision. That does not mean it has been withdrawn. In Standards Australia's aged-standards process, "Pending Revision" means the document has been flagged as needing an update. Until a replacement edition is actually published, AS/NZS 2201.1:2007 remains the current edition. The 2026 draft discussed in section 6 is that update, in progress. A draft is not the standard.
The official catalogue abstract describes it as specifying minimum requirements for the construction, installation, operation and maintenance of intruder alarm equipment and installed systems, including wire-free systems, for private premises, commercial premises and special installations, and as providing guidance for preparing a maintenance contract between a client and an alarm company. The published preface (in the public store preview) says the objective is to help insurers, alarm companies, equipment manufacturers, clients and the police arrive at a complete and accurate statement of the alarm system required for particular premises.
Equally important is what the standard, on its own official scope, does not do:
- It does not cover the transmission of signals from the client's premises to a remote monitoring centre. That is the job of AS/NZS 2201.5 (the transmission path) and AS 2201.2 (the monitoring centre).
- It does not specify the extent or degree of protection that has to be provided, and it does not claim to cover every requirement of a particular installation. How much of a building is protected, and to what class, is a design decision made with the client, not a single coverage recipe printed in Part 1.
Part 1 is one document in a family. The editions below are the ones listed as current on the Standards Australia store and Intertek Inform catalogues when this was researched on 22 November 2026 (Australia/Sydney). Always check the live catalogue before you specify a document in a contract.
- AS/NZS 2201.1:2007 — client's premises: design, installation, commissioning and maintenance (this part). Current, pending revision. 34 pages.
- AS 2201.2:2022 — Alarm and electronic security systems, Part 2: Monitoring centres. Current. Published 25 March 2022, 33 pages. This edition is designated AS, not AS/NZS, and the series title was widened from "Intruder alarm systems" to "Alarm and electronic security systems". It specifies requirements for the construction, equipment, staff and operation of centres that monitor client alarm and security systems, and it includes a grading system for those centres. ASIAL's monitoring-centre grading scheme is built around this standard. ASIAL stated that after 25 March 2024, AS 2201.2:2022 is required for new or renewal grading applications.
- AS 2201.3-1991 — detection devices for internal use. Still listed as current, also pending revision. Published 28 March 1991, 30 pages. This is a detector performance and test standard (passive infrared, microwave, ultrasonic, beam interruption, vibration, foil, pressure mats and so on). Its official abstract places special emphasis on characteristics that affect false-alarm susceptibility and tamper resistance. It is more than 30 years old; treat it as current only because the catalogue still says so, and confirm before you rely on it.
- AS 2201.4-1990 — wire-free systems installed in client's premises, with Amendment 1-1990. Still listed as current, pending revision. Only 6 pages. The 2007 edition of Part 1 already includes its own wire-free provisions, and the 2007 preface lists Parts 1, 2, 3 and 5, not Part 4. I have not compared the two documents clause by clause. If you are specifying a wireless system, confirm which document your contract, insurer or assessor actually wants.
- AS/NZS 2201.5:2008 — alarm transmission systems. Current. Published 31 January 2008, 21 pages, and reconfirmed in Australia on 18 September 2020 (it remains current in New Zealand as well, on Intertek Inform's note). This covers the performance, reliability and security of the path between the premises and the monitoring centre — dedicated paths, switched and digital networks, and wire-free links.
3. Who it applies to, and whether it is mandatory
Australian and New Zealand Standards are not automatically law. They become binding when legislation, a licence condition, a government policy, a contract, a tender or an insurance policy calls them up, or when someone chooses to design and certify a system against them. I have not found a statute that makes AS/NZS 2201.1:2007 compulsory for every alarm installed in Australia or New Zealand.
What I have verified is that official and industry bodies refer to it in several different ways. Those references are not all the same thing as a legal mandate:
Regulator guidance (should / ensure), not a substitute for the Act
- The NSW EPA's page on managing noise from intruder alarms says building intruder alarms should be installed in accordance with AS2201.1-2007, and tells owners to ask to see the installer's security licence. The legal time limits on how long a building alarm may sound (5 minutes if installed on or after 1 December 1997, 10 minutes if installed before that) come from the Protection of the Environment Operations (Noise Control) Regulation 2026, not from the standard.
- A November 2021 Western Australian Department of Water and Environmental Regulation fact sheet on audible alarms, still circulated by local government, tells people to have the system installed by a licensed security agent and to ensure it complies with AS/NZS 2201.1:2007. That is published guidance in a noise fact sheet, not a line I have traced into a WA Act that I can quote here.
- The South Australian Protective Security Framework physical-protections table uses "Class 3–4" and "Class 5" security alarm system language, and a footnote states that AS/NZS 2201.1 provides guidance on alarm systems. That is a government policy document using the standard as guidance and using its class vocabulary, for agency security zones. It is not a general rule for every house or shop.
- Several current units in the nationally recognised CPP Property Services training package tell technicians to review and apply AS/NZS 2201.1:2007. Examples include CPPSEC2021 Install security equipment and systems, CPPSEC3036 Program and configure security equipment and systems, and related units on testing, commissioning and routine service. Those units also describe the work as applying in extra-low-voltage environments as defined in AS/NZS 2201.1, and they still tell you to check the state licensing regulator. Completing a unit is not a substitute for a security licence.
- ASIAL runs a Class 5 certification program for control equipment, and a separate Class 5 certification for an installed intruder alarm system, both expressly with respect to AS/NZS 2201.1:2007. Certificates are valid for a nominal period of two years. For a site certification, a current Class 5 capability certification for the control equipment has to be verified before the site inspection. This is an industry assessment scheme, not a government licence, and it is aimed at the highest class, not at every domestic panel.
- ASIAL's better-known grading scheme is for monitoring centres, against AS 2201.2, not Part 1. Membership of ASIAL is not a licence and is not the same as grading or Class 5 certification.
- The New Zealand Security Association lists AS/NZS 2201.1:2007 and AS/NZS 2201.5:2008 as supporting documents to its 2023 Code of Practice – Security Systems: Electronic and Physical, and makes those standards available read-only to members. That is an industry code for members, not a finding that every NZ DIY alarm is required by statute to meet 2201.1.
The standard's own stated audience includes insurers, and it is common for a commercial specification, a government tender or a household insurance policy to ask for a system installed to AS/NZS 2201.1, sometimes with a stated class, and sometimes with monitoring at a centre graded to AS 2201.2. I have not found a general Insurance Council of Australia rule that every policy requires it. If your premium, claim or lease depends on it, read the actual policy wording or ask the insurer in writing. Do not take a salesperson's "it meets Australian Standards" line as proof.
Licensing is a separate question
In most Australian states and territories, installing, maintaining, repairing, servicing, selling or advising on security equipment as a business is a licensed security activity. The licence comes from the state or territory regulator, not from Standards Australia. See the licensing map. A licensed installer may still install a system that is not documented to 2201.1; a system specified to 2201.1 still has to be installed by someone who holds the right licence (and, where the work is electrical wiring work, the right electrical licence).
4. What the 2007 edition actually talks about
This section is a map of topics, based on the official table of contents, the public store preview of the opening clauses, and the catalogue abstracts. It is not a restatement of the requirements. I have not copied the classification tables, the battery rules or the maintenance intervals out of the standard.
Risk assessment and agreeing the class with the client
The public preview of the 2007 edition includes a risk-assessment requirement: before installation, a risk assessment is to be conducted and documented in conjunction with the client, and the classification of the installation is to be selected in accordance with Appendix A, with the client's agreement. Appendix A is titled "Application to risk profile". Section 3.16 then sets out equipment classification, Classes 1 to 5.
I am not reproducing what each class requires. What I can say from official industry material, not from quoting those clauses, is that ASIAL treats Class 5 as the highest security level, "suitable for protection up to an extreme business level." A government policy document (the SA framework above) also uses Class 3–4 and Class 5 language for agency alarm systems. If someone tells you a house alarm is "Class 5", ask them on what basis: the agreed risk profile, the control equipment certification, the detectors actually fitted, the signalling path, and the documentation. A high-class panel with low-class detection or no monitoring is not automatically a high-class system.
Design and detection coverage
Because Part 1 explicitly does not specify the extent or degree of protection, "installed to 2201.1" is not a synonym for "every window and hallway is covered." Coverage is what you agree in the risk assessment and the design. The installation section of the standard does address detection devices, zoning and end-of-line supervision. The performance of many internal detectors is the subject of the much older Part 3, not of Part 1.
Control equipment, location and tamper detection
The installation and equipment sections cover where control equipment and the power supply are located, how they are mounted, tamper detection, enclosures, terminals, marking of control equipment, and instructions. Those are design and workmanship topics. The standard also has a heading for "additional functionality" — I have not unpacked what that heading contains.
Power supplies and battery standby
There is a substantial block of requirements on power supplies: performance, low-battery reporting, automatic battery testing and fault reporting, charger design and rating, a mains-supply isolation switch, power-supply indications (mains, charging, battery), marking, and battery requirements including battery capacity. I am not stating a standby duration here. Figures of that kind belong in the standard and in the design for the actual load. If a quote claims a particular backup time, ask the installer to show how that was calculated against the standard and the equipment actually fitted.
Signalling and monitoring
Part 1 includes alarm transmission equipment on the premises and audible warning devices, but the path from the premises to a remote centre is Part 5, and the centre itself is Part 2. A local siren-only system and a dual-path monitored system are not the same product, even if the same panel is on the wall. If monitoring is part of the brief, ask which transmission method is used, whether the centre is graded, and what happens if one path fails. This forum already has a home for that discussion in Back to Base Monitoring Protocol Discussion.
Zoning, wiring and installation practice
The installation section covers general installation, wiring type and protection, stress on conductors, jointing, flexible connections, terminations, wire-free links, and environmental conditions (including special environments). "It was programmed" is not the same as "it was installed." Cable support, end-of-line supervision, tamper circuits and the location of the power supply are the sort of things a later technician, an insurer or an assessor will look at.
Commissioning, client training and handover
The standard has dedicated headings for commissioning and client training. Section 4 covers general operational procedures and responsibilities, including the client's responsibilities. A system that was never commissioned, or that was handed over without training, is a common source of false alarms and of "the alarm went off and nobody knew the code" call-outs. That is a practical observation; it is not a quoted clause.
Documentation, records and the right to disconnect
Section 6 covers client and equipment records, a maintenance record, authority for disconnecting, and a logbook. The catalogue abstract also mentions guidance for a maintenance contract. If you are the client, ask what you will be given at handover: the agreed class and risk assessment, as-built zone list, equipment list, codes and user instructions, monitoring account details, and how service visits will be recorded. If you are the incoming technician, ask for those records before you start changing the system.
Maintenance and service
Section 5 is "Maintenance and service", with headings for routine maintenance and emergency service. I am not stating how often a visit is required. Intervals, if they are specified, are in the standard and in the maintenance contract. A "set and forget" alarm with a 15-year-old lead-acid battery is a maintenance conversation, not a design badge.
False alarms
The public table of contents for Part 1 does not have a chapter titled "false alarm management". The standard still touches the problem through commissioning, client training, client responsibilities, environmental conditions, zoning, and — in Part 3 — detector performance and false-alarm susceptibility. Neighbourhood noise law is separate: in NSW, a building alarm that remains audible in a neighbouring residence beyond the legal time can attract a penalty, whether it sounded because of a break-in or because it was faulty. Operator error, open windows, pets and unmaintained sensors are still the everyday causes. A monitored system with a well-briefed client and a maintained battery will usually do more for the neighbours than a louder siren.
5. What this means for homeowners and DIY, and for installers
If you own the premises, or you are fitting a kit yourself
- Use 2201.1 as a checklist of questions, not as a badge you print on a DIY panel. Useful questions: was a risk assessment written down and agreed? Which class is being claimed, and why? What is actually detected, zone by zone? Where are the control equipment and the battery? What backup and what reporting does the power supply have? Is the system monitored, and if so by whom and over what path? What documentation and training do you get? What is the maintenance arrangement?
- "Compliant with AS/NZS 2201.1" is a specific claim. It means the design, equipment, installation, commissioning, documentation and maintenance were done against that edition. A retail kit, a video doorbell, or a Home Assistant alarm integration is not automatically a 2201 system, and connecting a compliant panel to a smart home does not, by itself, keep or break that status. If an insurer or a landlord has asked for compliance, get that requirement in writing and have a licensed installer address it.
- Licence rules for working on your own home are not the same in every state, and they are not the same as the rules for paid work on someone else's site. Read the licensing thread for your jurisdiction; do not assume a hobby install is automatically exempt, and do not assume that holding an electrician's licence is enough.
- Even a purely local siren still has to live with noise law (the NSW time limits above are one example) and with the ordinary rules about electrical work and cabling. CCTV you add beside the alarm has its own privacy rules — see the privacy thread. Electric locks on a required fire exit are a different standard again — see the maglock and egress thread.
- You need the current official text, not this forum post. Buy or view AS/NZS 2201.1:2007 (and, where the job includes monitoring or transmission, the current Part 2 and Part 5) from Standards Australia, Intertek Inform, or Standards New Zealand.
- You also need the right licence for that state or territory, and, where the work is electrical wiring work or regulated customer cabling, those tickets as well.
- If you offer Class 5 work, ASIAL's certification pathway is the industry scheme that exists today, and it has a formal prerequisite about Class 5-capable control equipment. Do not use "Class 5" as marketing language for a mid-range domestic panel.
- Do not install to an unpublished draft unless a client has expressly contracted to follow a named draft, and even then understand that the draft can still change and that 2007 remains the current published edition until a new edition is issued.
- Handover documents, a logbook and a clear maintenance agreement are part of doing this properly, not extras. So is telling the monitoring centre before you isolate or disconnect a live system — the standard has a heading for authority to disconnect, and the client's monitoring contract will have its own rules.
A replacement draft, designated DR AS/NZS 2201.1:2026, Intruder alarm systems, Part 1: Client's premises — Design, installation, commissioning and maintenance, was opened for public comment by Standards Australia committee EL-031 (now described as Alarm and Electronic Security Systems).
Standards New Zealand's joint-drafts page and an ASIAL public notice both give the comment closing date as 23 November 2026. ASIAL's notice also gives a comment start date of 21 September 2026. This post was researched on 22 November 2026 (Australia/Sydney), so that closing date was the following day. If you are reading this after 23 November 2026, the comment window may already have closed, or it may have been extended; check the live portal rather than this thread.
How to comment
Joint drafts in this series are commented on through the Standards Australia public comment portal, not by emailing this forum. You will need to register or log in, open the draft, and submit comments against it before the published closing date. Standards Australia publishes a help guide, GU 515c — Public Comment Portal Help Guide for Members of Public. Standards New Zealand's joint-drafts page points New Zealand submitters to the same Australian portal and to that help process. I have not used a logged-in session to walk the comment form, so treat the portal's own instructions as the authority if they differ.
What the committee itself says is changing
Standards New Zealand's published summary of the draft (the text also used on the joint-drafts list) says the objective is still to specify minimum requirements for design, installation, commissioning and maintenance, to help insurers, alarm companies, manufacturers, clients and the police achieve a complete and accurate statement of the system required for particular premises. It then states that the major changes in this edition include the addition of:
- (a) Risk assessment
- (b) Radio frequency techniques
- (c) Security class levels 1 to 5
The draft's own series list, in that same SNZ summary, still points to Parts 1, 2, 3 and 5. I have not seen a statement in that summary about the future of Part 4.
What a draft is not
A draft can change after comment, can be delayed, or can be recast. Until a new edition is published and listed on the official catalogue, AS/NZS 2201.1:2007 remains current. Do not treat DR AS/NZS 2201.1:2026 as the standard, and do not discard 2007 documentation on the strength of a draft summary.
7. Related threads on this site
- Who needs a licence to install alarms, CCTV or access control in Australia
- Australian electrical compliance for smart-home work
- Cameras, doorbells and NVRs: privacy, workplace notice, and audio
- Maglocks, emergency releases and fire-exit rules
- Back to Base Monitoring Protocol Discussion — the signalling side, which Part 5 and Part 2 address more directly than Part 1
- Brand-specific alarm forums under Alarm System Integration (Ness, Paradox, Bosch, Honeywell, Inner Range and others) — for product and integration detail, not for the text of the standard
Standards Australia store: AS/NZS 2201.1:2007
Standards Australia store: public preview of AS/NZS 2201.1:2007
Intertek Inform catalogue: AS/NZS 2201.1:2007 (status, abstract, table of contents)
Standards Australia store: AS 2201.2:2022
Standards Australia store: AS 2201.3-1991
Intertek Inform catalogue: AS 2201.3-1991
Standards Australia store: AS 2201.4-1990
Intertek Inform catalogue: AS 2201.4-1990
Standards Australia store: AS/NZS 2201.5:2008
Intertek Inform catalogue: AS/NZS 2201.5:2008 (including the 2020 reconfirmation note)
Standards New Zealand: joint draft standards, including DR AS/NZS 2201.1:2026 and the 23 November 2026 closing date
Standards Australia public comment portal
Standards Australia: GU 515c Public Comment Portal Help Guide for Members of Public
ASIAL: public notice that DR AS/NZS 2201.1:2026 is open for comment (21 September to 23 November 2026)
ASIAL: grading and certification (monitoring centres, Class 5 control equipment, Class 5 installations)
ASIAL monitoring centre grading / Class 5 flyer (2024)
ASIAL: application for Class 5 intruder alarm system installation certification (March 2023)
NSW EPA: managing noise from intruder alarms
WA Department of Water and Environmental Regulation: audible alarms fact sheet (November 2021), via Shire of Plantagenet
South Australian Protective Security Framework: PHYSEC1 Annex Table 2, physical protections for security zones
National training register: CPPSEC2021
National training register: CPPSEC3036
New Zealand Security Association: guidelines, codes of practice and standards
New Zealand Building CodeHub record for AS/NZS 2201.1:2007
Just Smart Homes t=251: security licensing in Australia
Just Smart Homes t=252: CCTV privacy
Just Smart Homes t=253: maglocks and fire-exit rules
This is not a substitute for AS/NZS 2201.1, not a compliance certificate, and not legal, insurance or licensing advice. The 2007 edition is paywalled and the 2026 draft sits behind the public-comment portal; I have not reproduced their clauses, and I have not treated the draft's published "additions" list as proof that the 2007 edition is silent on risk assessment, radio techniques or Classes 1 to 5. Standards, noise regulations, training packages and industry schemes change. Check the current official catalogue, the comment portal, and the regulator that applies to the job. Researched from official and industry sources on 22 November 2026 (Australia/Sydney). Please correct anything that has moved on.