Ness installer basics: P-commands, default codes, and when you need a licensed installer

Discuss Ness Alarm Systems, Including Smart Home Integrations
Post Reply
User avatar
ZerOne
Site Admin
Posts: 292
Joined: Sun Dec 13, 2020 8:21 am

What this thread is
A plain-English map of how programming access works on Ness D-series panels (DPlus, D8x/D16x Deluxe, D8XCEL/D16XCEL), the factory-default codes published in the official manuals, a short list of common P-options, and when to stop and call a licensed installer. It is a companion to the identification and Home Assistant threads in this forum.

It is not official Ness advice, not a complete programming manual, and not a licence to do security work. The authoritative document is the installer manual for your board and firmware. Option numbers and defaults do shift between DPlus, Deluxe and XCEL, and between firmware versions. If a setting matters on a live site, read that manual or ask Ness technical support (1300 551 991, techsupport@ness.com.au).

In Australia, installing, maintaining, repairing, servicing or (in many cases) programming alarm equipment for other people, or as a business, is a security-licence activity. The map of who needs which licence is in Who needs a licence to install alarms, CCTV or access control in Australia?. Mains work and some extra-low-voltage work also sit under electrical compliance. Intruder-alarm design, installation and maintenance is also covered by AS/NZS 2201.1 — this thread does not quote that paid standard.

Complexity
Reading: beginner to intermediate. Changing installer options on a monitored or professionally maintained system is work you should not improvise.

1. Two program modes, and why installer mode is not a place to linger
On DPlus, Deluxe and XCEL, the official manuals describe the same basic path. The panel must be disarmed.
  • User program mode — press P + [master code] + E. The PROG indicator is on (not flashing). This is for user codes, entry/exit times, some clock and SMS numbers, and similar owner-level options. On DPlus, the manual says the panel drops back to operating mode if no key is pressed for four minutes.
  • Installer program mode — from user program mode, press P + [installer code] + E. The PROG indicator flashes. This unlocks all program options.
  • Exit — P + E returns to operating mode (PROG off).
Two official warnings matter in the real world:
  • While the panel is in installer program mode, all inputs are disabled. That is convenient when you are working on tampers and detectors, and it is a serious gap if you walk away and leave the panel in program mode on a site that is supposed to be protecting something.
  • NessComms direct-connect via the serial port requires installer program mode. On older D8x/D16x manuals, installer mode also makes the panel answer incoming telephone calls so NessComms can connect by dial-up. Do not leave a panel sitting in installer mode "so the software can find it".
First-time power-up of a new board is a special case: powering up with the PROG/TAMP link off puts the panel straight into installer program mode. That is a factory commissioning step, not a method described here for bypassing an unknown installer code on a panel that is already in service.

2. Factory-default codes — change them
The current DPlus, Deluxe and XCEL installer manuals all publish the same factory defaults:
  • Master code (User Code 1): 123
  • Installer code: 000000
Those values are in the official manuals so a new panel can be commissioned. They are also the first thing an installer should change. A panel still running 123 / 000000 is effectively unlocked to anyone who has read the manual.

User (keypad) codes on these panels are typically 3 to 6 digits and must not start with 0. The installer code is programmed at P99E (enter the new code twice). User Code 1, the master code, is programmed at P201E (on these panels the user-code range runs through to P256E, for up to 56 codes). Changing the master and installer codes is one of the first jobs on any new or inherited system — and if the system is monitored, agree the change with the people who hold the codes for service.

3. Reading the firmware version
In user or installer program mode, P99999999E (eight 9s) displays the firmware version on the zone LEDs. The manuals' example is version V6.1 flashing as 6, then 1. On a Navigator, the Info control can also show a D8x/D16x version. Write the version down before you ask for help or compare option lists: a V7.8 Deluxe, a V11.5 XCEL and a V12 DPlus do not have identical menus.

Related special functions in the same manuals (also entered as a string of identical digits while in program mode) include a siren test and a panel microprocessor reset (P88888888E, eight 8s). The DPlus manual's tip is to use that reset before a short power-down if you want the real-time clock and the time-until-next-test-call saved. These are service functions, not day-to-day user commands.

4. Common P-options you will see discussed
This is a map, not a substitute for the option tables in the manual. Defaults and even which sub-options exist differ by model.
  • P199E — serial output / two-way ASCII data. Options 1E–6E turn on address, timestamp, alarms, warnings, access events and zone seal state (6E from V6 onward). Factory default is off. This is the option the Home Assistant integration and Ness-Bridge / iComms paths need. DPlus also has 7E (send test ASCII data).
  • P86E — communicator / reporting format. The exact flags depend on the panel. On XCEL 4G and DPlus, official tables include 1E (disable communicator), 2E (Contact ID) and 3E (ArmorIP). On D8x/D16x Deluxe (landline dialler), the quick-start and option notes use 2E for Contact ID and other flags for audible / combined formats — there is no ArmorIP flag in the same place, because Deluxe is not the onboard-4G panel. Read the page for your model before you toggle these, and talk to the monitoring centre first.
  • P70E / P72E (and XCEL/DPlus IP equivalents such as P170E) — reporting telephone number or ArmorIP address/port, and the client account number issued by the monitoring centre.
  • P95E — clear radio devices assigned to zones (does not clear user codes).
  • P96E — clear the short keypad alarm-memory display (the DPlus manual says this does not clear the Navigator's longer 80-event log).
  • P97E — clear panel options / restore factory defaults. On DPlus this restores program options other than user codes and radio codes, and the manual notes that it also deletes radio devices programmed on zones.
  • P98E — clear user codes (keypad codes, radio keys and access cards) and restore User Code 1 to 123. The DPlus, XCEL and Deluxe manuals state that this does not clear the installer code.
  • P99E — program a new installer code.
NessComms, when you are entitled to it (Ness describes it as free for trade users), is the supported way to do a full option review, download logs, and keep a client database. DPlus needs NessComms V6.00 or later. The panel has to be in installer program mode for a direct serial connection.

5. Defaulting a panel safely — and what these options will not do
"Factory default the panel" is three different jobs on these boards, and they are easy to confuse:
  • P97E puts program options back to factory values. Zone types, timers, reporting flags and similar options go with it. User codes are meant to survive this one; radio devices on zones may not.
  • P98E wipes user codes back to a single master code of 123. It will not rescue you if the installer code is unknown, because it does not reset P99E.
  • Doing both, plus P95E, is the combination the DPlus power-up notes use when onboard memory has not initialised cleanly (P95E, P97E and P98E, then a brief power cycle). That is a commissioning recovery, and it still assumes you can already enter installer program mode.
Before any of that on a site that is already in use:
  • Tell the monitoring centre if the panel reports off-site. A default will change account numbers, formats and test-call behaviour.
  • Tell the occupiers. Codes, radio keys and access cards may stop working.
  • Write down or export the current programming (NessComms or a commissioned option list) if you might need to put it back.
  • Do not default a panel as a way of "getting in" when the installer code is unknown. If you do not have the installer code, contact the original installer or Ness technical support. This thread will not describe ways to bypass that code.
6. When to call a licensed installer
Call (or hire) a licensed security equipment specialist, and where needed a licensed electrician, rather than working through a forum post, when:
  • you are doing the work for someone else, or as a business — that is the core of the licensing map in t=251
  • the system is monitored, or is a condition of insurance, and you are about to change reporting, codes or zone configuration
  • you do not have the installer code, or you cannot identify the board and firmware
  • you need new mains-rated power supplies, detectors run on building wiring, or any work that is electrical wiring work in your state or territory
  • the site has to meet AS/NZS 2201.1 design, commissioning or maintenance requirements, or a client specification that cites that standard
  • you are adding or changing access control on a required exit — that is a fire-egress problem as well as an alarm problem; see maglocks, emergency releases and fire-exit rules
  • a default, a failed programming session, or a communicator change has left the site unprotected or unable to report
If you are the owner of a system in your own home, that does not automatically make every modification lawful or wise, and it does not make a forum post a substitute for the manual. When in doubt, stop, leave the panel in operating mode, and get someone licensed for that work in your state or territory.

Official starting points
Ness DPlus Installation & Programming Manual, 890-511 Rev 1.12 (PDF)
Ness D8x/D16x Deluxe Installation & Programming Manual, 890-017 Rev 2.5D (PDF)
Ness D8/D16 XCEL 4G Installation & Programming Manual, 890-490 Rev 1.14 (PDF)
Ness technical support and branch contacts
Just Smart Homes t=251: security licensing in Australia
Just Smart Homes t=239: electrical compliance
Just Smart Homes t=253: maglocks and fire-exit rules

This is not official Ness advice, not legal advice, and not a complete programming reference. Factory-default codes are published in the official installer manuals so a new panel can be commissioned; they should be changed before a system is put into service. Option numbers and behaviour vary by model and firmware — check the current manual for your board. Researched from official documentation on 22 November 2026 (Australia/Sydney). Please correct anything that has moved on.
Post Reply

Return to “Ness Alarm System Discussion”