Zigbee chips and modules compared (2026): EFR32MG21/MG24, TI CC2652/CC2674, nRF52840, ESP32-H2/C6, adapters

Discuss the Implementation and Development of Zigbee Devices
Post Reply
User avatar
ZerOne
Site Admin
Posts: 292
Joined: Sun Dec 13, 2020 8:21 am

Threads here often ask "which stick?". This is a look at what is inside, using vendor datasheet pages, product pages and project docs as at October 2026. I have not benchmarked any of these. Range depends heavily on antenna, board, firmware and your house, so treat the numbers as datasheet figures only. For adapter categories, Zigbee2MQTT support levels and TI suffixes, see the network design and coordinator buying guide thread. This one is about the silicon.

Silicon Labs EFR32MG21 vs MG24
  • MG21: Silicon Labs says it is optimised for line-powered Zigbee, Thread and Bluetooth mesh. Datasheet page: -104.3 dBm sensitivity (802.15.4), up to +20 dBm on the 20 dBm parts (others are 10 dBm class), RX 9.4 mA, TX 9.9 mA at 0 dBm and 34.9 mA at 10 dBm, Cortex-M33 at up to 80 MHz, up to 1024 kB flash and 96 kB RAM. Used in the Sonoff ZBDongle-E and Home Assistant Connect ZBT-1.
  • MG24: -105.4 dBm sensitivity (802.15.4), TX up to 19.5 dBm on the high-power parts, RX 5.1 mA, TX 5 mA at 0 dBm, 19.1 mA at 10 dBm and 156.8 mA at 19.5 dBm, Cortex-M33 at 78 MHz, up to 1536 kB flash and 256 kB RAM. It also lists Matter, OpenThread, Zigbee and Bluetooth LE support and Secure Vault security. Used in the Connect ZBT-2.
  • Pros: both list Zigbee, Thread and BLE support. MG24 has lower current draw and more memory on paper.
  • Cons: the stack is Silicon Labs' commercial EmberZNet, so firmware is built with their SDK and tools. Many part numbers are only 10 dBm class, so "MG24" on its own does not tell you the output power. The ZBT-2 page lists 10 dBm in Europe and 8 dBm for the rest of the world.
Texas Instruments CC2652 / CC1352 / CC2674
  • CC2652P: TI lists it as a Cortex-M4F multiprotocol 2.4 GHz MCU with an integrated power amplifier (Zigbee 3.0, Thread, BLE). TI's page marks a newer alternative as available (CC2340R2/R5, different pinout, +8 dBm, "lower price"), so check before designing it into anything new.
  • CC2674P10: Cortex-M33, 1 MB flash, integrated PA. TI's page lists Zigbee coordinator, router, end device and NCP among its supported roles.
  • SMLIGHT's SLZB-06 range is sold with a choice of CC2652P, CC2652P7, CC2674P10, EFR32MG21, MG24 and MG26 chips, which is a handy way to compare in one product line.
  • Pros: Z-Stack firmware for these chips is published in Koenkk's Z-Stack-firmware repo.
  • Cons: check the P (power amplifier) vs R suffix when ordering.
Nordic nRF52840
  • Nordic's page: 64 MHz Cortex-M4 with FPU, 1 MB flash, 256 KB RAM, +8 dBm TX power, and Bluetooth LE, 802.15.4, Thread and Zigbee protocol support, plus USB 2.0.
  • Zigbee comes via Nordic's add-ons. The older R22 add-on is in maintenance mode and not recommended for new designs. The R23 add-on (ncs-zigbee) supports nRF52840 and is what Nordic points new work to. The stack inside is ZBOSS, which Nordic describes as third-party and precompiled.
  • Pros: ESPHome's Zigbee component supports nRF52.
  • Cons: +8 dBm without an external amplifier, and the ESPHome docs list a limit of 8 endpoints on nRF52.
Espressif ESP32-H2 and ESP32-C6
  • ESP32-H2: single-core RISC-V, 802.15.4 plus Bluetooth 5 LE, no Wi-Fi. Espressif says it is certified as a Zigbee-compliant platform and supports Thread and Zigbee.
  • ESP32-C6: Wi-Fi 6, Bluetooth 5 LE and 802.15.4 in one chip.
  • ESPHome's docs say the H2 seems to work more reliably than the C6, and mention reports of C6 boards that only work next to the coordinator. They also note Wi-Fi station mode plus a Zigbee router gives an unstable network, and Wi-Fi access point plus Zigbee is not supported.
  • Pros: supported by Espressif's ESP-Zigbee-SDK and by ESPHome.
  • Cons: the Wi-Fi plus router limitations above apply.
What I could not verify
Telink's site lists Zigbee and Thread support in its multiprotocol SoCs, and NXP's JN516x family is an older name you will see in legacy gear. I could not open usable spec pages for specific Telink or NXP parts, so I have left their numbers out rather than guess.

Adapters built on these chips
  • Sonoff ZBDongle-E: EFR32MG21, shipped with EmberZNet firmware (6.10.3 on the product page I read). Sonoff says the official firmware supports 21 direct children by default and up to 40.
  • Connect ZBT-1: EFR32MG21, up to +20 dBm, Zigbee 3.0 with Thread via firmware. Home Assistant says its multiprotocol firmware is experimental and not recommended.
  • Connect ZBT-2: MG24, ESP32-S3 as the USB bridge, recommended MSRP US$49. Zigbee or Thread, not both at once. There is an experimental repeater firmware.
  • SMLIGHT SLZB-06U: Ethernet, PoE or USB-C, switchable between Zigbee coordinator, router and Matter-over-Thread border router.
Zigbee plus LoRa on one board
I only found early or niche examples, so treat them as ideas, not recommendations. A third-party project listing describes the LILYGO T-Lora C6 as an ESP32-C6 with an SX1262 LoRa radio, but I did not verify Zigbee working on that board. Kampi/IoT-Gateway on GitHub describes an open hardware gateway combining Zigbee, Thread and LoRa. I have not evaluated it. LoRa is covered in the LoRa forum.

Links The Silicon Labs and Nordic pages blocked my command-line fetch but open fine in a normal browser.

Question for the group: Which chip family is in your coordinator, and have you noticed a real-world difference in range or stability after swapping?
Post Reply

Return to “Zigbee Wireless Technology”